|
|
|
|
| Application Chart |
Diagrams |
Application
Notes |
|
| 2000 Suzuki DRZ 400 |
|
OEM: 47 |
| 2001 Suzuki DRZ 400 |
|
OEM: 47 |
| 2002 Suzuki DRZ 400 |
|
OEM: 47 |
| 2003 Suzuki DRZ 400 |
|
OEM: 47 |
| 2004 Suzuki DRZ 400 |
|
OEM: 47 |
| 2005 Suzuki DRZ 400 |
|
OEM: 47 |
| 2006 Suzuki DRZ 400 |
|
OEM: 47 |
| 2007 Suzuki DRZ 400 |
|
OEM: 47 |
| 2008 Suzuki DRZ 400 |
|
|
| 2007 Suzuki DRZ 400 SM |
|
|
| 2008 Suzuki DRZ 400 SM |
|
|
|
|
|
|
|
|
|
|
|
|
| WARNING: Laws concerning this product vary from state/province to state/province. Your state/province may prohibit its use on public roads or restrict its use to novelty, show use, off-road areas, or race facility areas only. In some states/provinces off-road uses are also prohibited. The manufacturer and retailer assume no responsibility for any use or application of this product in violation of any applicable law. Before installing this product, please check your state/provincial and local/municipal laws and regulations. |
|
| The Q&A on this Product |
|
|
| QUESTION: I have a ccm 644 which is a dr650 engine, standard sprocket is 15f - 48r. what would you suggest for more acceleration, off road use only and if new chain would be required. many thanks |
| ANSWER: 14-48 and you can use your stock chain if its good |
|
| QUESTION: The motorcycle shop I am purchasing my DRZ400s (04)from has suggested a 14-46 sprocket change for more acceleration and not too much loss of top end, is this correct, If not what would you suggest. Thank you |
| ANSWER: yes sounds good its all about ehat you are trying to get try that and make adjustments later if you need |
|
| QUESTION: What is the standard factory sprocket setup for a DRZ400s 04 model. I would like more acceleration and a do bit of off road, what would be the ideal setup for that. Thanks |
| ANSWER: 15-47 WITH 116 LINK CHAIN |
|
| QUESTION: if i don't want to change my front sprocket on my drz400s what is a good rear sprocket for highway use |
| ANSWER: 39 |
|
| QUESTION: if I change my sprocket to 16-39 for highway use on my drz400s will I need to purchase a new chain |
| ANSWER: YOU SHOULD YES |
|
| QUESTION: I want the perfect combo for going as slow as possible with this bike. I will change the chain if need be. I am content at 2 miles an hour it is for hunting will not be on the streets.
|
| ANSWER: use 13 53 you will need a shorter chain |
|
| QUESTION: I have a drz400e that I have 2 sets of wheels for, but both of the rear rims are 18" (not the typical 17" SM rim) with 48 tooth rear sprockets on both of them. Front sprocket is 14. I want to make one set of wheels for highway, one set for trail. How many rear teeth do you recommend for highway with 18" rims? Would I still be able to bump the front sprocket up to 16 teeth? |
| ANSWER: 16 FRONT 41 REAR FOR THE 18" WHEEL SET |
|
| QUESTION: does a counter sprocket of 2000-2006 drz400sm fit on a 2007 |
| ANSWER: YES IT DOES |
|
| QUESTION: Hi. I just purchased item 5028-520 in black (39 teeth) and item 1024-520 (16 teeth). Do I need a new chain or do I need to modify my old chain? Please provide item number also in case that I need a new chain. Thank you. |
| ANSWER: IF YOUR CHAIN IS NEW YOU CAN USE YOUR OLD ONE IF ITS OLD PLEASE REPLACE OT WITH A:
520 SRX 110 LINKS |
|
| QUESTION: How am I suppose to order a sproket from you ?
When I go on line and get to the checkout, the screen goes blank. I called your (303) phone no. and spent 34 min. on hold !!!!!!!!!!!
Phil, |
| ANSWER: Hi, this site is no longer active due to a registrar problem. Please order the parts on www.powersportsfx.com. They are the same and more. We apologize for the confusion. |
|
| QUESTION: ok i bought a 13 tooth drive sprocket form you 2 weeks ago i have called sat on hold sent you emails and still cannot get ahold of anyone at this place please contact me on the location of the order number 9189 |
| ANSWER: please call (303) 330-0477 ask for mark |
|
| QUESTION: What is the stock sprockets on my 2006 DRZ400S? |
| ANSWER: 15-44 |
|
| QUESTION: I have an 07 DRZ400S and ride mostly on the highway. It seems like my RPM's are way too high. What do you recommend for sprockets? I heard that a larger front sprocket will not fit on this bike, is that true? |
| ANSWER: yes order a 16 front and your problems are solved |
|
| QUESTION: im looking for more low end power for tricks but still wanna keep speeds of 65 to 70 without burning the engine what ratio would be best on a drz 400 sm 08 |
| ANSWER: try 15-43 or just change the front to a 14 |
|
| QUESTION: I have a stock 2001 DRZS. I would like more torque and significantly slower speeds during hunting season. What should I change the rear sprocket to? |
| ANSWER: 47 will make a diff! |
|
| QUESTION: Hi Guys
I ride a 2003 drz400.
My bike is set with 14 front 47 rear sprockets,
What is the best sprocket combinatins for highway /touring use. Will I also need a new chain? |
| ANSWER: 16-39 |
|
| QUESTION: I'm trying to order a sprocket but because of security issues i cannot. Also I seem to be having a problem finding your phone number anywhere.Could you tell me what it is so I can finally place this order? |
| ANSWER: (303) 330-0477 |
|
| QUESTION: If I order a sprocket for an '07 will I have any problems installing that on a '08 DRZ400SM? |
| ANSWER: no they are the same |
|
| QUESTION: If I order a 39 tooth rear sprocket for my DRZ400SM which is a 2008, would it matter if the sprocket was for an '07? |
| ANSWER: no they are the same |
|
| QUESTION: I want to place an order but your site has a security issue, can I order via telephone ? |
| ANSWER: yes |
|
| QUESTION: I have a 2008 DRZ400SM and I want to drop teeth in my rear stock sprocket so I can cruise at 70mph or so comfortably, in a low rpm. How many teeth do you recommend for the rear to accomplish that? |
| ANSWER: 39 |
|
| QUESTION: what is the best number of teeth for a 2002 drz 400e to run a little highway and alot of everyday driving on the roads |
| ANSWER: 16 TOOTH FRONT |
|
| QUESTION: this might seem like a silly question, but I have a standard drz400, and I am looking for more top end speed. what rear sprocket do you recommend. |
| ANSWER: go down to a 43 |
|
| QUESTION: yea i do alot of canyon riding on my drz 400sm and i cant seem to keep up with the street bikes? what and how many teeth should my sprocket be in the front and rear? thanks |
| ANSWER: 16-39 |
|
| QUESTION: QUESTION: I was thinking about changing my front back to stock and putting a 38 tooth on the back, will that give me ample top end and drop my rpm's? I don't care about wheelies or hole shotting on the street, I actually ride this sucker on the highway, and I think now the rpm's are WAY too high. Is that the answer to my problem?(2007 DRZ400SM)
ANSWER: yes it will 16-39 is the best combo for hwy use
I was the guy that asked this question, and I accidentally deleted your response, could you please give me the price and availability of the 16 and 39 please. |
| ANSWER: they are both in stock and posted on the site if you can't find it please call customer service. |
|
| QUESTION: i want to slow my bike down to use on the farm .i am currently running 15 /50.
can you recomend a ratio for farm and trail riding |
| ANSWER: 14-48 |
|
| QUESTION: I was thinking about changing my front back to stock and putting a 38 tooth on the back, will that give me ample top end and drop my rpm's? I don't care about wheelies or hole shotting on the street, I actually ride this sucker on the highway, and I think now the rpm's are WAY too high. Is that the answer to my problem?(2007 DRZ400SM) |
| ANSWER: yes it will 16-39 is the best combo for hwy use |
|
| QUESTION: can i use 14 teeth in front and 53 teeth at Rear on my 350 dr and what other things i need to change ? p.s this is offroad use only |
| ANSWER: you can just make sure you have enogh clerance |
|
| QUESTION: Does DRZ400 48 teeth is a steel sprockets? |
| ANSWER: NO ITS ALLUMINUM |
|
| QUESTION: looking for a 39 tooth rear sprocket for a DRZ400SM, 2007- black in color |
| ANSWER: in stock part number 5028-520-39bk if you don't see it on this site please call customer service.
DRIVEN RACING |
|
| QUESTION: I NEED TO PURCHASE CHAIN,SPROCKET REAR & FRONT DO U HAVE THEM IN STOCK,
SUZUKI DRZ 400S
MODEL 2000 |
| ANSWER: yes we do rear is 5028-520- number of teeth chain is the mrd-6 and front is a 1024-520-number of teeth or call customer service 720-891-4907.
DRIVEN RACING |
|
| QUESTION: Dose this sprocket come in the gold color? |
| ANSWER: YES IT DOES GO TO WWW.DRIVENRACING.COM TO SEE THE COLOR
driven racing |
|
|
|
| Ask your question here: |
|
| Your email (so we can send you the answer): |
|
|
|
Event Schedule
powered by